As an important equipment for processing in the electric power industry, electrical appliance industry wiring harness and automobile industry, the automatic terminal machine has multiple functions such as feeding, cutting, stripping and crimping. Once a failure occurs, it will seriously hinder production. The wiring harness plays an important role in new energy vehicles. This article introduces you to the fully automatic cable terminal machine, which faults are often encountered during use, and fault analysis and solutions.
a. It may be that the wire feed wheel is too tight or too loose; adjust the straightener to be able to play the role of straightening and can be sent out smoothly.
b. The thread cutting edge is worn or the cutting edge; replace with a new one.
2. The length of the peeling opening is differenta. The wire feed wheel is pressed too tightly or loosely; adjust the gap between the two wheels with the wire roller fine-tuning piece so that the wire is not flattened or too loose and slips.
b. The cutting blade is too shallow or too deep; use the cutting blade depth adjustment to adjust the blade to the appropriate position, so as not to damage the copper wire and smoothly peel off the rubber.
c. The cutting and peeling knife is worn or the cutting edge; replace with a new cutting blade.
3. The machine cannot start running or stops during operationa. Check for current input (220V) and 6KG air pressure;
b. Check whether the total number of settings has been reached, if it has to be reset, power off and restart;
c. Check if there is a wireless material or a running part is stuck;
d. Check whether the terminal machine has signal connection or power connection and the terminal machine is not pressed.
4. Uneven copper wire pressing on the terminala. Check whether the gun-type swing arm catheter is attached to the wire;
b. Check whether the blade of the terminal machine is relatively straight with the swing arm catheter;
c. Check whether the auxiliary pressing block of the terminal machine is loose;
d. Check if there is any change in the distance between the terminal machine and the automaton.
5. The terminal machine is very noisyIt is normal for the terminal machine to have a slight noise. If the noise is too loud, it may be:
a. There is wear between certain parts and components of the terminal machine, resulting in increased friction;
b. The screw of the terminal machine is loose during work, which causes the jitter of the parts to increase.
6. The motor of the terminal machine does not rotateCheck whether the clutch position of the terminal machine is correct and whether the fuse is burnt out.
7. The terminal machine appears to hit continuouslya. Check whether the switch near the main shaft of the terminal machine is damaged or the screws are loose;
b. Check whether the circuit board and pedal of the terminal machine are broken;
c. Check whether the moving rod spring of the terminal machine falls off or breaks and loses its elasticity, and whether the moving rod is damaged.
8. No response from terminal machinea. Check whether the power cord of the terminal machine is connected or whether there is a problem with the line;
b. Check whether the circuit board of the terminal machine is intact or damaged;
c. Check whether each switch of the terminal machine can be used;
d. Check whether the pedal of the terminal machine is burnt out;
e. Check whether the electromagnet of the terminal machine is magnetic or burned.
Custom Made Length 35 cm USB C to iOS Phone Cable Cord, Right Size Angle for DJI Mini 2/3 Pro/Mavic Air 2 / Mavic 3 Remote Controller & iPhone, iPad Devices
Compatible for DJI Mini 2, Maivc 3 pro & Mavic Air 2 Remote Controller,works for iPhone/iPad Device
Perfect length (35cm) and right angle Connecting when you use tablet holder for drones with the devices.
Unique 90 Degree Plug Provides a slim fit in narrow spaces.
This cable can transfer data and charger with all iOS Device
Custom Requirements
In addition to the off the shelf offerings Technical Cable Applications skilled specialists are ready to help with any custom cable assembly requirements you might have. UCOAX stocks cables by the thousands and can custom build anything not on hand. Please contact the UCOAX Technical Sales Team for assistance with all your cable assembly needs.
Drone Cable,Drone Battery Charger Cable,Drone Cables,Drone Controller Cable
UCOAX , https://www.ucoax.com